Get a quote
Guide · Damp

Damp-proof injection in old houses: is it the right fix?

If you own an older house with damp walls, someone will probably suggest injecting a chemical damp-proof course. Sometimes it has a place. Often the damp has a different cause, and the injection does not fix it.

Georgian terrace with painted front doors, railings and a basement area

In short

  • True rising damp is rarer than often believed, and it is regularly misdiagnosed.
  • Most damp in old houses comes from ground levels, gutters, leaks, condensation or the wrong materials.
  • Solid walls are meant to take in moisture and let it dry out. Sealing them can make things worse.
  • Find and fix the cause first, then see whether the wall dries before treating it.

How solid walls deal with moisture

Georgian, Victorian and Edwardian houses mostly have solid brick walls laid in lime mortar, with lime plaster inside. Many have no damp-proof course, or an early one. These walls were never meant to be completely dry. They take in some moisture and let it evaporate out through the porous brick, mortar and plaster.

That works well as long as the wall can breathe and water is kept away from it. Trouble starts when something stops the wall drying, or soaks it faster than it can dry.

Why damp is so often misdiagnosed

The SPAB describes true rising damp as rarer than commonly perceived but regularly misdiagnosed. A common reason is reliance on an electrical moisture meter. These meters read conductivity, and salts left in old plaster can give high readings on a wall that is fairly dry.

Damp low on a wall can also come from rain splashing off paving, high ground levels, leaking gutters and downpipes, plumbing leaks or condensation. Historic England notes that low-level condensation mould is often mistaken for rising damp. An injection does nothing for any of these.

What injection involves, and the drawbacks

A chemical damp-proof course is a water-repelling fluid or cream injected into holes drilled along a mortar joint near the bottom of the wall. It is usually sold with the plaster hacked off to a metre or so and replaced with a dense cement-based render to hold back salts.

In a solid lime-built wall, that dense render and any waterproof coatings stop the wall breathing, so moisture can be pushed higher or into the bricks. Irregular old walls with rubble cores or mixed materials are also hard to treat evenly. And if the real cause was outside, the damp continues.

The SPAB advises caution with retrofit damp-proof courses in pre-1919 buildings, and suggests a written second opinion from an independent surveyor if you are unsure of a recommendation.

Diagnose the cause first

  • Check outside ground levels against the damp-proof course or internal floor.
  • Look at gutters, hoppers, downpipes and gullies, ideally in heavy rain.
  • Check air bricks are clear and the space under any timber floor is ventilated.
  • Look for hard cement render, pointing or plaster, and waterproof paints.
  • Rule out plumbing leaks and condensation, especially in kitchens, bathrooms and bedrooms.

What usually works instead

Fixing the cause, then letting the wall dry. That might mean lowering ground levels, repairing rainwater goods, clearing air bricks, removing cement render or repointing in lime. Salt-laden plaster can then be replaced in lime, and the wall finished in a breathable paint.

This is staged work, and a damp wall can take months to dry out. It is not as quick as an injection, but on an old house it deals with the problem rather than covering it. In one case, several firms had recommended injection to a customer of ours. The cause turned out to be high ground levels outside.

Questions

Does damp-proof injection work?

It can reduce genuine rising damp where it is properly diagnosed and installed. The problem is that much damp in old houses is not rising damp, so an injection does not address the cause, and the dense render that often goes with it can stop a solid wall drying.

My mortgage survey says I have rising damp. What should I do?

Surveys often flag high meter readings and recommend a specialist. Before agreeing to injection, have someone look for the causes outside and around the wall. If you are buying, get the work priced before you exchange.

Get a quote

Describe the project and where it is. We’ll reply to arrange a visit, then send an itemised written quote.

  1. We reply within 2 working days
  2. We visit and look at the project properly
  3. You get an itemised, provisional quotation

Rather talk it through? Call or WhatsApp Lee on 07875 545032.

Photos help. Send them from the contact page or reply to our email with them.

What’s it about?

We reply to every enquiry within 2 working days. Your details are only used to reply about this project.

Enquiry sent

Thanks, that’s with LR Building

We reply to every enquiry within two working days.

Not heard back by then? Call or WhatsApp Lee on